• Designed & manufactured for drying coating of eyeglass lenses
• Maximum operating temperature up to 100°C 
• Inner dimension  : Width 1100 mm x Depth 1100 mm x Height 500 mm
• SUS 304 Stainless Steel plate interior
• Double leaf air tight swing doors
• Forced convection with :
  • Hot air re-circulating system
  • Horizontal air flow, side to side blowing direction
• Built-in oven electrical control panel
• Microprocessor based digital indicating temperature controller
• Overheat protection system
• Digital timing system for soaking / holding process
• Industrial process RTD PT100 temperature sensor
• On/off heating control (optional: Full proportional heating control).

Spare Parts Warranty : 1 Year (Normal Operation)

• Designed & manufactured for heat treatment automotive parts
• Maximum operating temperature up to 150°C 
• Inner dimension  : Width 650 mm x Depth 650 mm x Height 600 mm
• SUS 304 Stainless Steel plate interior
• Single leaf air tight swing doors
• Forced convection with :
  • Hot air re-circulating system
  • Combination air flow from both side oven wall return to top wall
• Remote floor standing type electrical control panel
• Microprocessor based digital indicating temperature controller
• Overheat protection system
• Digital timing system for soaking / holding process
• Industrial process RTD PT100 temperature sensor
• Full proportional heating control by SCR power regulator
• Custom work piece rack & rack carrier. (optional)

Spare Parts Warranty : 1 Year (Normal Operation)

• Designed & manufactured for heat treating automotive dash panel
• Maximum operating temperature up to 280°C
• Inner dimension : Width 700 mm x Depth 1650 mm x Height 875 mm
• SUS 304 Stainless Steel interior
• Pneumatic lifting up door
• Pneumatic work piece sliding table (carrier)
• Manual adjustable air inlet and exhaust dumper
• Exhaust system ( Exhaust blower & exhaust hood ) at work piece loading & unloading side
• Forced convection with :
  • Hot air re-circulating system
  • Horizontal air flow, side to side blow direction
• Oven wall mounting type electrical control panel
• One touch operating system
• PLC ( Programmable Logic Control ) control circuit
• Microprocessor based digital indicating temperature controller
• Overheat protection system
• Digital timing system for soaking / holding process
• Industrial process thermocouple sensor
• On / off heating control with 6 Nos staging heating power (Optional: Full proportional heating control)

Spare Parts Warranty : 1 Year (Normal Operation)

• Designed & manufactured for preheating material (epoxy) inside drum
• Capable to load 2 drum (Each size: dia. 500 mm x Height 700 mm )
• Maximum operating temperature up to 200°C 
• Inner dimension  : Width 1680 mm x Depth 845 mm x Height 1300 mm
• SUS 304 Stainless Steel plate interior
• Manual operated double leaf swing door
• Manual adjustable air inlet and exhaust dumper
• Ramp adjustable conveyor table with pneumatic stopper between preheating & stirring section
• SUS 304 stirrer & vacuum pipe
• Motorized stirrer by geared motor
• Stirred & vacuum pipe pneumatic lifter
• Pneumatic actuated dripped collecting tray
• Forced convection with :
  • Hot air re-circulating system
  • Horizontal air flow, side to side air flow by 2 Nos circulation blower
• Oven wall mounting type electrical control panel
• PLC ( Programmable Logic Control ) control circuit
• Full installed sensor part on chamber door, collecting tray , stirrer (position & rotation sensor), compressed air pressure switch & vacuum pressure switch.
• Microprocessor based digital indicating temperature controller
• Overheat protection system
• Digital timing system for soaking / holding process
• Industrial process thermocouple sensor
• Pulse heating control by Solid State Contactor ( SSC ).

Spare Parts Warranty : 1 Year (Normal Operation)

• Designed & manufactured for jet spinner parts cleaning ( Textile industries )
• Maximum operating temperature up to 500°C (Normal: 450°C )
• Inner dimension   : Width 1080 mm x Depth 750 mm x Height 1200 mm
• SUS 304 Stainless Steel plate interior
• SUS 304 steam spraying pipe
• Manual operated double leaf swing door 
• Pneumatic actuated air inlet and exhaust dumper
• Pneumatic actuated steam nitrogen valve
• Forced convection with :
  • Hot air re-circulating system
  • Vertical air flow, from top wall return to bottom wall
• Remote floor standing type electrical control panel
• PLC ( Programmable Logic Control ) control circuit
• Full installed sensor part on bomb shell blasting door, steam & compressed air piping line
• Programmable temperature controller
• Overheat protection system
• Digital timing system for soaking / holding process
• Industrial process thermocouple sensor
• Full proportional heating control by SCR power regulator

Spare Parts Warranty : 1 Year (Normal Operation)

• Designed and manufactured for pre heating ceramic stalk of LPDC (Low Pressire Die Casting) Machine
• Maximum operating temperature up to 350°C (Working: 300°C)
• Inner dimension : Width 1000 mm x Depth 465 mm x Height 900 mm
• Sus 304 Stainless steel plate interior
• Manual operated double leaf swing door
• Free / Natural convection heating system
• Heat is transferred from the bottom up through the work load and exits through vents in the top
• Oven wall mounting type electrical control panel
• Microprocessor based digital indicating temperature controller
• Overheat protection system
• Digital timing system for soaking / holding process
• Industrial process thermocouple sensor
• Full proportional heaitng control by SCR power regulator

• Designed & manufactured for stress relieving automotive parts
• Maximum operating temperature up to 400 °C
• AMS 2750 E Class 2 Standard (Uniformity : ± 6 °C)
• Inner dimension : Width 700 mm x Depth 600 mm x H 700 mm
• SUS 304 Stainless Steel plate interior
• Air tight single leaf manual swing door
• Forced convection with:
  • Hot air re-circulating system
  • Dual air flow, heated air provided from both (Left & Right) side of oven chamber wall and pulled upward through the work piece
• Manual adjustable exhaust dumper
• Remote floor standing type electrical control panel
• Microprocessor based digital indicating chamber temperature controller that meet AMS 2750 E requirement. (Accuracy: ± 2 °F / 1.1 °C )
• System Accuracy Test (SAT) & Temperature Uniformity Survey (TUS) Port Installed.
• Equipped Overheat protection system by chamber & Heat Source overheat protector controller.

Spare Parts Warranty : 1 Year (Normal Operation)

This up to 400 °C aerospace-grade oven with nitrogen (EO-02) was manufactured for the embrittlement process of aeroplane parts requiring a nitrogen (N2) based environment. This oven was designed to conform to various AMS 2750 aerospace pyrometry standards.

• Maximum operating temperature up to 400 °C
• AMS 2750 E Class 2 Standard (Uniformity: ± 6 °C)
• Inner dimension: Width 700 mm x Depth 600 mm x Height 700 mm
• SUS 304 Stainless Steel plate interior
• Airtight single leaf manual swing door
• Forced convection with:
  • Hot air re-circulating system
  • Dual airflow, heated air provided from both (Left & Right) side of oven chamber wall and pulled upward through the work piece
• Forced exhauster with automatic (Motorized) Fresh air inlet and exhaust dumper
• Installed with nitrogen gas purging system.
• Remote floor standing type electrical control panel
• Microprocessor-based digital indicating temperature controller that meet AMS 2750 E requirement. (Accuracy: ± 2 °F / 1.1 °C )
• System Accuracy Test (SAT) & Temperature Uniformity Survey (TUS) Port Installed.
• Equipped Overheat protection system by chamber and heat Source overheat protector controller.
• Industrial metal sheathed thermocouple type N completed with UKAS calibration certificate. (AMS 2750E Calibration Accuracy Type)
• Full proportional heating control by SCR power regulator
• 6 Channel Paperless thermo recorded that meets AMS 2750 E requirement. (Accuracy: 0.04 °C )

Warranty

• 1-year spare parts and services warranty

• Designed & Manufactured for Oven Storage of Automotive production parts
• Maximum operating temperature up to 360 °C (Working Temperature : 300 °C )
• Inner Dimension : WIdth 850 mm x Depth 600 mm x Height 750 mm
• SUS 304 Stainless Steel interior
• Air tight single leaf manual swing door
• Forced convection heating system with :
  • Hot air re-circulating system
  • Horizontal blow, side to side blowing direction
• Manual adjustable sliding dumper
• Oven wall mounting type electrical control panel
• Microprocessor based digital indicating temperature controller
• Overheat protection system
• Industrial process thermocouple sensor
• Full proportional heating control by SCR Power Regulator (Very good linear control, high accuracy, fast response, able to keep steady temperature well and extend heater life)