Top

INDUSTRIAL OVENS

Embrittlement Oven Without N2 (EO-01)
Specification

  • Designed & manufactured for stress relieving automotive parts
  • Maximum operating temperature up to 400 °C
  • AMS 2750 E Class 2 Standard (Uniformity : ± 6 °C)
  • Inner dimension : Width 700 mm x Depth 600 mm x H 700 mm
  • SUS 304 Stainless Steel plate interior
  • Air tight single leaf manual swing door
  • Forced convection with:
    • Hot air re-circulating system
    • Dual air flow, heated air provided from both (Left & Right) side of oven chamber wall and pulled upward through the work piece
  • Manual adjustable exhaust dumper
  • Remote floor standing type electrical control panel
  • Microprocessor based digital indicating chamber temperature controller that meet AMS 2750 E requirement. (Accuracy: ± 2 °F / 1.1 °C )
  • System Accuracy Test (SAT) & Temperature Uniformity Survey (TUS) Port Installed.
  • Equipped Overheat protection system by chamber & Heat Source overheat protector controller.

Spare Parts Warranty : 1 Year (Normal Operation)

Embrittlement Oven With N2 ( EO-02 )
Specification

  • Designed & Manufactured for embrittlement process aeroplane parts.
  • Maximum operating temperature up to 400 °C
  • AMS 2750 E Class 2 Standard (Uniformity : ± 6 °C)
  • Inner dimension : Width 700 mm x Depth 600 mm x H 700 mm
  • SUS 304 Stainless Steel plate interior
  • Air tight single leaf manual swing door
  • Forced convection with:
    • Hot air re-circulating system
    • Dual air flow, heated air provided from both (Left & Right) side of oven chamber wall and pulled upward through the work piece
  • Forced exhauster with automatic (Motorized) Fresh air inlet and exhaust dumper
  • Installed with nitrogen gas purging system.
  • Remote floor standing type electrical control panel
  • Microprocessor based digital indicating temperature controller that meet AMS 2750 E requirement. (Accuracy: ± 2 °F / 1.1 °C )
  • System Accuracy Test (SAT) & Temperature Uniformity Survey (TUS) Port Installed.
  • Equipped Overheat protection system by chamber & Heat Source overheat protector controller.
  • Industrial metal sheathed thermocouple type N completed with UKAS calibration certificate. (AMS 2750E Calibration Accuracy Type)
  • Full proportional heating control by SCR power regulator
  • 6 Channel Paperless thermorecorder that meet AMS 2750 E requirement. (Accuracy : 0.04 °C )

Spare Parts Warranty : 1 Year (Normal Operation)

Bench Oven ( BO-05 )
Specification

  • Maximum operating temperature up to 500°C
  • Inner dimension : Width 500 x Depth 500 x Height 500 (mm)
  • Outer dimension : Width 1120/1725 mm x Depth 810/1020 mm x Height 1360/1630 mm (Approx
  • SUS 310 & 304 Stainless Steel interior
  • Mild Steel exterior finished by Jotun Protective paint
  • Forced convection with:
    • Hot air recirculating heating system
    • Horizontal flow and side to side blowing direction
    • Heater Power : 9 kW
  • Air tight single leaf manual swing door
  • Manual adjustable air inlet and exhaust dumper
  • Oven wall hanging type electrical control panel
  • Microprocessor based digital indicating temperature controller
  • Overheat protection system
  • Industrial process thermocouple sensor
  • Full proportional heating control by SCR Power Regulator (Very good linear control, high accuracy, fast response, able to keep steady temperature well and extend heater life)

Spare Parts Warranty : 1 Year (Normal Operation)

Storage Oven ( SO-01 )
Specification

  • Designed & Manufactured for Oven Storage of Automotive production parts
  • Maximum operating temperature up to 360 °C (Working Temperature : 300 °C )
  • Inner Dimension : WIdth 850 mm x Depth 600 mm x Height 750 mm
  • SUS 304 Stainless Steel interior
  • Air tight single leaf manual swing door
  • Forced convection heating system with :
    • Hot air re-circulating system
    • Horizontal blow, side to side blowing direction
  • Manual adjustable sliding dumper
  • Oven wall mounting type electrical control panel
  • Microprocessor based digital indicating temperature controller
  • Overheat protection system
  • Industrial process thermocouple sensor
  • Full proportional heating control by SCR Power Regulator (Very good linear control, high accuracy, fast response, able to keep steady temperature well and extend heater life)

Cartridge Filter Drying Oven (CFDO-01)
Specification

  • Designed & Manufactured for Cartridge Filter Drying Process
  • Maximum Operating temperature up to 90 ºC
  • Inner dimension : Width 3000 mm x Depth 1000 mm x Height 1600 mm
  • Mild steel plate interior & exterior
  • Air tight double leaf manual swing door
  • Forced convection system with :
    • Hot air re-circulating system
    • Horizontal air flow from side to side blowing direction
    • Single zone heating control with steam heating radiator source
  • Oven wall mounting type electrical control panel
  • Mircoprocessor based digital indicating temperature controller
  • Overheat protection system
  • Digital timing system for soaking / holding process
  • Industrial process thermocouple sensor
  • Equipped with pulse steam heating control
  • Equipped with automatic door switch (safety interlock  circuit)

Top Loading Oven (TLO-05)
Specification

  • Maximum operating Temperature Up to 315 °C
  • Inner dimension : Width 600 mm x Depth 1100 mm x Length 4000 mm
  • Temperature Uniformity : ± 6 °C (Empty Load Condition)
  • SUS 304 Stainless Steel Interior
  • Mild steel exterior finished by Jotun Protective Paint
  • Industrial rockwool insulation       
  • Forced convection with :
    • Hot air re-circulation heating system
    • Horizontal blow and side to side blowing direction
  • Automatically operated swing up door actuated by pneumatic air cylinder, sealed by hi-temp door gasket
  • Installed with 6 Number of Access port holes for Inserting Test pipe
  • Manual adjustable fresh air inlet and exhaust dumper
  • Installed with System Accuracy Test (SAT) & Temperature Uniformity Survey (TUS) Port
  • Microprocessor based digital indicating temperature controller with Re-transmission output PV (Present Value) or SV(Set Value) Communication
  • Digital timing system for holding / soaking process
  • Overheat protection system controlled by :
    • Oven chamber temperature limiter
    • Heat source chamber overheat protector
    • Recirculating air flow safety switch
    • Electrical interlock system between circulation blower & heater element
  • Full proportional heating control by SCR Power Regulator
  • Industrial process thermocouple type K temperature sensor
  • 1 Year Sparepart & Services Warranty (Normal Operation)

Walk In Drying Oven (WIDO-03/4000)
Specification

  • Designed and manufactured for drying automotive parts
  • Maximum temperature up to 200 °C
  • Inner dimension (approx.) : Width 2165 mm x Depth 1200 mm x Height 1600 mm
  • SUS 304 Stainless Steel Interior
  • Mild steel exterior finished by Jotun protective paint
  • Industrial Rockwool insulation
  • Air tight swing double leaf door sealed by high temperature gasket
  • Manual adjustable Fresh air inlet and exhaust dumper
  • Forced convection heating system with:
    • Hot air re-circulating system
    • Combination air flow, from both side oven wall return to top wall
  • Oven wall mounting type electrical control panel
  • Microprocessor based digital temperature controller
  • Overheat temperature protection system controlled by:
    • Heat source temperature limiter
    • Electrical interlock system between circulation blower & heater power switching control
  • Industrial process thermocouple sensor
  • Full proportional heating control by SCR Power Regulator
  • Optional: Transfer Trolley & Workpiece trolley
  • 1 Year Spare part & services Warranty (Normal Operation)

Cabinet Drying Oven (CDO-01)
Specification

  • Used for Drying Aeroplane Metal Parts
  • Maximum Working Temperature Up to 260 °C (Operating Temperature : 200 °C)
  • Build to meet AMS 2750E Standard Requirement
  • Inner Dimension (Approx.) : Width 950 mm x Depth 1100 mm x Height 1500 mm
  • SUS 304 Stainless Steel Interior
  • Mild steel exterior finished by Jotun protective paint
  • Air tight single leaf manual operated swing door sealed by heat resistant gasket
  • Forced convection with :
    • Hot Air re-circulating system
    • Horizontal air flow, side to side blowing direction
  • Manual fresh air inlet and exhaust outlet swing dumper
  • Oven wall mounting type electrical control panel
  • Microprocessor based digital indicating temperature controller that meet AMS 2750E requirement (Accuracy: ±1,1 °C)
  • Equipped with Overheat protection system by chamber temperature limiter & heater overheat protector controller
  • Industrial metal sheathed thermocouple type N completed with UKAS Calibration Certificate to AMS 2750E
  • Full proportional heating control by SCR power regulator
  • 1 Year Spare part & services Warranty (Normal Operation)

Walk In Drying Oven (WIDO-04/3200)
Specification

  • Maximum operating Temperature up to 250 °C
  • Volume (Capacity) : ± 3200 Litre
  • Inner Dimension (Approx.) : Width. 1900 mm x Depth. 1000 mm x Height 1700 mm
  • SUS 304 Stainless Steel Interior
  • Mild Steel exterior finished by Jotun protective paint
  • Industrial rockwool insulation
  • Air tight double leaf manual swing door
  • Manual adjustable air inlet and exhaust dumper
  • Forced convection system with :
    • Hot air re-circulating system
    • Horizontal air flow, side to side blowing direction return to upper ceiling
  • Oven wall mounting type electrical control panel
  • Microprocessor based digital temperature controller
  • Overheat temperature protection system controlled by :
    • Chamber temperature limiter
    • Hi-limit alarm of chamber temperature control
    • Electrical interlock system between circulation blower & heater power switching control
  • Digital timing system for soaking/holding process
  • Industrial process thermocouple Type K temperature sensor
  • Full proportional heating control by SCR Power Regulator
  • Optional :  SUS 304 Trolley & Workpiece Tray
  • Optional :  Paperless thermorecorder
  • 1 year Sparepart & services Warranty (Normal Operation)

CALL US NOW
Office (+62) 21 556 62 440
Bpk. Sumber +62) 811 170 320
Bpk. Harli (+62) 813 885 63 000

COME VISIT US
Sentra Prima Tekno Park Blok E No. 12 RT.003 RW.003 Tangerang Banten 15137
SEND US A MESSAGE
Customer Service:
cs@smindo.co.id